Electronics
25 tools
Calculators for everyday electronics work and classic circuits you can build and probe on a virtual breadboard. Values follow the usual standards (IEC 60062 for resistor colours, IEC 60751 for RTDs) and every result shows the formula behind it.
Calculators and tables11
- Ohm's LawSolve voltage, current, resistance and power from any two
- Resistor Color CodesDecode resistor color bands
- LED ResistorSeries resistor for an LED, with the nearest standard value
- Voltage DividerOutput voltage, or the resistor needed for a target voltage
- Parallel & Series ResistanceTotal resistance or speaker impedance of several parts
- RC Filter CutoffCutoff frequency of low-pass and high-pass RC filters
- RTD and Thermocouple TablesPt100, Pt500 and Pt1000 per IEC 60751 and NIST thermocouples K, J, T, E, N, S, R, B, in both directions with cold-junction compensation
- 4–20 mA Signal ScalingConvert 4–20 mA and 0–10 V to process units and PLC counts, with NAMUR limits, square-root flow and loop burden
- Event Power CalculatorBalance loads over three phases: neutral, breaker, cable drop, generator and CEE outlets
- UPS Runtime CalculatorHow long a UPS holds a load, from battery energy or the maker’s runtime table, and whether the load fits in watts and VA
- Unit ConverterLength, mass, temperature, volume, speed and more
Breadboard circuits12
- Breadboard simulatorBuild circuits on a virtual breadboard with real parts and see them work: LEDs that light and burn out, 555 timers, transistors, regulators, logic, a multimeter and warnings. Top view or 3D.
- Electronic component libraryResistors, capacitors, diodes, Zeners, transistors, MOSFETs, LEDs, 7-segment displays, regulators and common ICs in 3D on a breadboard, with pinouts and the key datasheet figures.
- LED with resistor on a breadboardStep-by-step 3D breadboard guide: LED, series resistor computed for your supply and colour, holes, schematic and measurements.
- Voltage divider on a breadboardStep-by-step 3D breadboard guide: two resistors for the ratio you need, loaded and unloaded output, schematic and measurements.
- RC low-pass filter on a breadboardStep-by-step 3D breadboard guide: RC low-pass for your cutoff frequency, resistor from the E-series, schematic and expected attenuation.
- 555 astable LED flasher on a breadboardStep-by-step 3D breadboard guide: NE555 astable with frequency and duty from R1, R2 and C, LED resistor, pin numbers and measurements.
- 555 monostable timer on a breadboardStep-by-step 3D breadboard guide: NE555 one-shot with a trigger button, pulse length T = 1.1 R C, LED and measurements.
- NPN transistor switch on a breadboardStep-by-step 3D breadboard guide: BC547 or PN2222A driving an LED or a relay coil, base resistor, flyback diode and pinout.
- Inverting op-amp (LM358) on a breadboardStep-by-step 3D breadboard guide: inverting amplifier on a single supply, gain from Rf and Rin, half-supply reference and LM358 pins.
- Non-inverting op-amp (LM358) on a breadboardStep-by-step 3D breadboard guide: non-inverting amplifier, gain 1 + Rf/Rg, output limit, bandwidth and LM358 pins.
- 7805 voltage regulator on a breadboardStep-by-step 3D breadboard guide: 5 V from a 9 to 12 V supply with a 7805, capacitors, heat dissipated and pinout.
- Button debounce RC on a breadboardStep-by-step 3D breadboard guide: tact button with a pull resistor and a capacitor to remove contact bounce, time constant and measurements.
Practice2
Other areas
- ConnectorsPinouts and wiring in 3D, male and female, checked against each standard.
- Audio & stageLevels, delays and loudness, DMX and event power, music and ear training.
- Industry & workshopModbus, 4–20 mA, RTDs, ZPL labels, cut lists and building materials.
- ComputersPower supply sizing, RAM compatibility, disk health, airflow and racks.
- Code & dataJSON, YAML, CSV and SQL, encoders, regex, networks and a code editor.
- Text & imagesClean up text, compress and crop images, colours, QR codes and passwords.
- Maths & businessPercentages, units, dates, interest, costing, ROI, CVs and trip planning.
- ScienceA 3D chemistry lab and a 3D engine lab with a dyno, tuning and fault diagnosis.
- MagicMagic tricks in 3D that you watch, take apart and practise.
- GamesTruco, escoba, chess, solitaires, puzzles and arcade classics.